1262: bump embedded-storage-async to 0.4 r=Dirbaio a=mehmetalianil
I just haven't found a way to revert the altered stm-metapac contents due to building.
Co-authored-by: Mehmet Ali Anil <mehmet@grusbv.com>
> dirbaio: so I was checking how zephyr does UARTE RX on nRF
> dirbaio: because currently we have the ugly "restart DMA on line idle to flush it" hack
> dirbaio: because according to the docs "For each byte received over the RXD line, an RXDRDY event will be generated. This event is likely to occur before the corresponding data has been transferred to Data RAM."
> dirbaio: so as I understood it, the only way to guarantee the data is actually transferred to RAM is to stop+restart DMA
> dirbaio: well, guess what?
> dirbaio: they just count RXDRDY's, and process that amount of data without restarting DMA
> dirbaio: with a timer configured as counter https://github.com/zephyrproject-rtos/zephyr/blob/main/drivers/serial/uart_nrfx_uarte.c#L650-L692
> dirbaio: 🤔🤷⁉️
> dirbaio: someone saying you can do the "hook up rxdrdy to a counter" trick, someone else saying it's wrong 🤪https://devzone.nordicsemi.com/f/nordic-q-a/28420/uarte-in-circular-mode
So we're going to do just that!
- BufferedUarte is lock-free now. No PeripheralMutex.
- The "restart DMA on line idle to flush it" hack is GONE. This means
- It'll work correctly without RTS/CTS now.
- It'll have better throughput when using RTS/CTS.
The UARTETWISPIn naming is quite horrible. With the nRF53, Nordic realized this
and renamed the interrupts to SERIALn. Let's copy that for our peripheral names, in nrf53 and nrf91.
If the user requests some configuration, but UICR is already programmed
to something else, detect this and warn the user.
We don't do it for the debug port settings, because if they are wrong
then the user will simply not be able to read debug logs.
- APPROTECT enable/disable. Notably this fixes issues with nrf52-rev3 and nrf53 from locking itself at reset.
- Use NFC pins as GPIO.
- Use RESET pin as GPIO.
NFC and RESET pins singletons are made available only when usable as GPIO,
for compile-time checking.
Obtaining the current WDT config is important so that we do not have to duplication configuration around the place. A constructor method has been introduced that returns WDT config in accordance with how the register is presently configured. The bootloader example has also been updated to show the watchdog can be obtained and used.
It's a perfectly fine thing to do, should be just a noop. Erroring is
really annoying when you're writing a payload to uart that might
be zero-length or not.
1069: GPIOTE InputChannel with mutable reference. r=Dirbaio a=Ardelean-Calin
Adding these changes enables us to define a channel using a mutable reference to `GPIOTE_CH(n)`, similar to how we can do with other drivers. So instead of using:
```rust
let p = embassy_nrf::init(config);
let freq_in = InputChannel::new(
p.GPIOTE_CH0,
Input::new(&mut p.P0_19, embassy_nrf::gpio::Pull::Up),
embassy_nrf::gpiote::InputChannelPolarity::HiToLo,
);
```
we can use:
```rust
let p = embassy_nrf::init(config);
let freq_in = InputChannel::new(
&mut p.GPIOTE_CH0,
Input::new(&mut p.P0_19, embassy_nrf::gpio::Pull::Up),
embassy_nrf::gpiote::InputChannelPolarity::HiToLo,
);
```
therefore not giving ownership to GPIOTE_CH0.
Co-authored-by: Ardelean Călin Petru <ardelean.calin@outlook.com>
Co-authored-by: Ardelean Calin <ardelean.calin@proton.me>
1056: embassy-nrf: Add TWIS module r=Dirbaio a=kalkyl
Verified to be working on nrf9160
Co-authored-by: kalkyl <henrik.alser@me.com>
Co-authored-by: Henrik Alsér <henrik.alser@me.com>
Adding these changes enables us to define a channel using a mutable reference to `GPIOTE_CH(n)`, similar to how we can do with other drivers.
So instead of using:
```rust
let freq_in = InputChannel::new(
p.GPIOTE_CH0,
Input::new(&mut p.P0_19, embassy_nrf::gpio::Pull::Up),
embassy_nrf::gpiote::InputChannelPolarity::HiToLo,
);
```
we can use:
```rust
let freq_in = InputChannel::new(
&mut p.GPIOTE_CH0,
Input::new(&mut p.P0_19, embassy_nrf::gpio::Pull::Up),
embassy_nrf::gpiote::InputChannelPolarity::HiToLo,
);
```
1042: embassy-nrf: Add SPIS module r=Dirbaio a=kalkyl
Verified to be working on nrf9160
Co-authored-by: Henrik Alsér <henrik.alser@me.com>
Co-authored-by: Henrik Alsér <henrik.alser@ucsmindbite.se>
Co-authored-by: kalkyl <henrik.alser@me.com>
959: Generic, executor-agnostic queue implementation r=ivmarkov a=ivmarkov
Hopefully relatively well documented.
Implementation relies on a fixed-size `SortedLinkedList` from `heapless`. (By default, for up to 128 timer schedules, but we can lower this number to - say - 64.)
As discussed earlier, on queue overflow, the `WakerRegistration` approach is utilized, whereas the waker that is ordered first in the queue is awoken to make room for the incoming one (which might be the waker that would be awoken after all!). Wakers are compared with `Waker::will_wake`, so the queue should actually not fill up that easily, if at all.
I've left provisions for the user to manually instantiate the queue using a dedicated macro - `generic_queue!` so that users willing to adjust the queue size, or users (like me) who have to use the queue in a complex "on-top-of-RTOS-but-the-timer-driver-calling-back-from-ISR" scenario can customize the mutex that protects the queue.
The one thing I'm not completely happy with is the need to call `{ embassy_time::queue::initialize() }` early on before any futures using embassy-time are polled, which is currently on the shoulders of the user. I'm open to any ideas where we can get rid of this and do it on the first call to `_embassy_time_schedule_wake`, without introducing very complex combinations of critical sections, atomics and whatnot.
Co-authored-by: ivmarkov <ivan.markov@gmail.com>
Co-authored-by: Dario Nieuwenhuis <dirbaio@dirbaio.net>
855: PDM microphone support for nrf r=Dirbaio a=pbert519
PDM microphones have a long startup phase, therefore the driver samples continuously and only switches the target buffer if the user requests sampling.
Co-authored-by: pbert <pbert@posteo.net>
This commit removes some of the code duplication for UarteWithIdle at the expense of requiring a split. As the example illustrates though, this expense seems worth the benefit in terms of maintenance, and the avoidance of copying over methods. My main motivation for this commit was actually due to the `event_endtx` method not having been copied across.
958: Implement proper `Drop` for `BufferedUarte` r=lulf a=ZoeyR
The drop method in `BufferedUarte` was prone to hanging indefinitely and also didn't actually disable the peripheral. I mostly copied over the drop method from `Uarte` with some modifications since `BufferedUarte` could have a transmit lasting indefinitely.
Co-authored-by: Zoey Riordan <zoey@dos.cafe>
936: Add split() method to BufferedUarte in embassy-nrf r=ZoeyR a=ZoeyR
I haven't completed testing this yet. I'm creating this PR early so that I can get corrected if I went way off course.
This PR adds a `split()` method to `BufferedUarte` as discussed on matrix.
Co-authored-by: Zoey Riordan <zoey@dos.cafe>
938: Do not use cfg_if for embedded-hal-async feature gates. r=Dirbaio a=Dirbaio
Old code used `cfg_if!` because rustc still parses code inside disabled cfg's, and Rust stable at that time couldn't parse the new GAT where-clause location. This is not the case anymore.
bors r+
Co-authored-by: Dario Nieuwenhuis <dirbaio@dirbaio.net>
Old code used `cfg_if!` because rustc still parses code inside disabled cfg's, and Rust stable at that time couldn't parse the new GAT where-clause location. This is not the case anymore.
Ensures that nRF saadc sampling is stopped and is awaited prior to exiting the two sampling methods. Not doing so causes a potential power drain and the potential for dropped buffer writes when having finished continuous sampling.
876: Add defmt support to embassy-embedded-hal errors r=Dirbaio a=matoushybl
`defmt::unwrap!()` should now work with shared buses. I tested it only with I2C as I don't have SPI in the target project.
Co-authored-by: Matous Hybl <hyblmatous@gmail.com>
871: nrf/saadc: add type-erased AnyInput. r=Dirbaio a=Dirbaio
872: nrf/usb: prevent user code from constructing a PowerUsb directly. r=Dirbaio a=Dirbaio
PowerUsb must be constructed through `new()` so that it sets up the IRQ.
It must have at least one private field, otherwise user code can construct
it directly with `PowerUsb{}`.
Co-authored-by: Dario Nieuwenhuis <dirbaio@dirbaio.net>
PowerUsb must be constructed through `new()` so that it sets up the IRQ.
It must have at least one private field, otherwise user code can construct
it directly with `PowerUsb{}`.
810: Takes care of power for nRF USB devices r=Dirbaio a=huntc
Modifies the usb-serial example to illustrate how to setup USB for situations where the USB power can be detected and removed.
Gaps:
~~* No support for the nrf-softdevices as yet, although this should be possible via another constructor.~~
* No support for the nrf5340, although this should be possible via USBREG.
The change is tested and appears to work. Some notes:
* There's an existing field named self_powered as a UsbDevice field. It doesn't ever appear to get set. I'm wondering if this field is intended to signal that a device has the nRF VBUS power situation or not. I'm not presently using it.
* The new PowerDetected event is generated on the bus initially in situations where just new is used i.e. without power management, including on STM. We can therefore rely on this event always being generated.
Old description:
~~EnabledUsbDevice is a wrapper around the `UsbDevice` where its enablement is also subject to external events, such as `POWER` events for nRF. It is introduced generically to support other platforms should they also require external signaling for enablement.~~
Co-authored-by: huntc <huntchr@gmail.com>
Eliminated a signal by using a simpler trait method that returns whether VBus power is available. Also includes a UsbSupply that can be signalled for use with the nRF softdevice. Includes the requirement for waiting for power to become available.
Allow creating UarteRx/UarteTx directly. This allows using uart unidirectionally
(rx-only or tx-only), without having to 'waste' a pin for the unused direction.
It currently contains whoever was first to write some code for the crate,
even if many more people have contributed to it later.
The field is "sort of" deprecated, it was made optional recently:
https://rust-lang.github.io/rfcs/3052-optional-authors-field.html
Due the the reasons listed there I believe removing it is better than
setting it to generic fluff like "The Embassy contributors".
- Move Interrupt and InterruptExecutor from `embassy` to `embassy-cortex-m`.
- Move Unborrow from `embassy` to `embassy-hal-common` (nothing in `embassy` requires it anymore)
- Move PeripheralMutex from `embassy-hal-common` to `embassy-cortex-m`.
Following the project's decision that "leak unsafe" APIs are not marked as "unsafe",
update PeripheralMutex to accept non-'static state without unsafe.
Fixes#801
788: Misc USB improvements, for stm32 r=Dirbaio a=Dirbaio
See individual commit messages.
These changes help implementing the driver for STM32 USBD (#709)
Co-authored-by: Dario Nieuwenhuis <dirbaio@dirbaio.net>
768: nrf/usb: fix control out transfers getting corrupted due to ep0rcvout sticking from earlier. r=Dirbaio a=Dirbaio
bors r+
Co-authored-by: Dario Nieuwenhuis <dirbaio@dirbaio.net>
The stack reads its own descriptors to figure out which endpoints
are used in which alt settings, and enables/disables them as needed.
The ControlHandler has a callback so it can get notified of alternate
setting changes, which is purely informative (it doesn't have to do anything).
* Adds implementations of embedded-storage and embedded-storage-async
for QSPI
* Add blocking implementations of QSPI
* Use blocking implementation in new() and embedded-storage impls
* Use async implementation in embedded-storage-async impls
* Add FLASH_SIZE const generic parameter
* Own IRQ in Qspi to disable it on drop
657: Async usb stack r=Dirbaio a=Dirbaio
TODO
- [x] Make it work on nRF
- [x] Add a way for classes to handle their own EP0 control requests - thanks `@alexmoon!`
- [x] Handle CONTROL OUT requests with data.
- [ ] Impl AsyncRead/AsyncWrite for CDC ACM -- will do later, it's not trivial
- [x] Cleanup unwraps/asserts/panics
- [x] Cleanup logs (make everything trace/debug, not info)
- [ ] Port synopsys-usb-otg
- [ ] Port stm32-usbd
- [ ] Add more classes? HID, MSD?
Co-authored-by: Dario Nieuwenhuis <dirbaio@dirbaio.net>
Co-authored-by: alexmoon <alex.r.moon@gmail.com>
640: Skip EasyDMA slice location check for empty slices and copy data if necessary r=Dirbaio a=TilBlechschmidt
As discussed, this PR makes the following changes:
- Ignore pointer location of zero-length slices (fixes#631)
- Change default functions so they copy the tx buffer if it does not reside in RAM
- Introduce new variants for `write`, `transfer`, and their blocking versions which fails instead of copying
- Add documentation about the motivation behind all these variants
<img width="984" alt="image" src="https://user-images.githubusercontent.com/5037967/155415788-c2cd1055-9289-4004-959d-be3b1934a439.png">
Remaining TODOs:
- [x] Change copying behaviour for other peripherals
- [x] TWI
- [x] UART
- [x] Add module-level documentation regarding EasyDMA and `_from_ram` method variants
`@Dirbaio` it probably makes sense for you to review it now before I "copy" over the changes to the other two peripherals.
Co-authored-by: Til Blechschmidt <til@blechschmidt.de>
Starting the sampling task prior to starting the SAADC peripheral can lead to unexpected buffer behaviour with multiple channels. We now provide an init callback at the point where the SAADC has started for the first time. This callback can be used to kick off sampling via PPI.
We also need to trigger the SAADC to start sampling the next buffer when the previous one is ended so that we do not drop samples - the major benefit of double buffering.
As a bonus we provide a calibrate method as it is recommended to use before starting up the sampling.
The example has been updated to illustrate these new features.
613: Rust stable support r=Dirbaio a=Dirbaio
This PR adds (limited) stable Rust support!
The drawbacks are:
- No `#[embassy::task]`, `#[embassy::main]`. (requires `type_alias_impl_trait`). You have to manually allocate the tasks somewhere they'll live forever. See [example](https://github.com/embassy-rs/embassy/blob/master/examples/nrf/src/bin/raw_spawn.rs)
- No async trait impls (requires GATs). Note that the full API surface of HALs is still available through inherent methods: #552#581
- Some stuff is not constructible in const (requires `const_fn_trait_bound`), although there's an (ugly) workaround for the generic `Mutex`.
So it's not that bad in the end, it's fully usable for shipping production-ready firmwares. We'll still recommend nightly as the default, until GATs and `type_alias_impl_trait` are stable.
Co-authored-by: Dario Nieuwenhuis <dirbaio@dirbaio.net>
591: PWM WS2812B example and flexible sequence config r=Dirbaio a=huntc
I've permitted the PWM sequences to be mutated on stopping the PWM by associating them with a new `SingleSequencer` structure. This is so that we can perform effects on the LEDs (and other use-cases, I'm sure!). The example has been updated to illustrate the use of this by flashing a WS2812B LED.
There's also a `Sequencer` structure for more sophisticated PWM interactions, along with a `pwm_double_sequence` example to illustrate.
These changes should make it possible to attain all of the nRF PWM functionality available.
Co-authored-by: huntc <huntchr@gmail.com>
This approach owns the sequence buffers which, while introducing an extra move, it eliminates the need to guard the lifetime of the sequence buffer. Given ownership, the buffer will be retained until the PWM sequence task is stopped.
Demonstrates how to set the colour of a WS2812B to blue using PWM, and the use of multiple sequences along with their own config. This required an API change.
I had introduced a small bug in my last PR where I assigned the sequence before stopping the PWM. I now stop the PWM before doing that now.
Also, corrected a math comment.
Sequences are now passed in via the start method to avoid having to stop the PWM and restart it. Sequences continue to be constrained with the same lifetime of the Pwm object itself. The pwm_sequence example has been extended to illustrate multiple sequences being passed around.
This commit allows event_endtx to be used outside of the Uarte itself. As a consequence, PPI can be used to drive tasks given the end of transmission on the Uarte. This is particularly useful for situations like RS485 where a GPIO must be set to high when transmitting then cleared when done. A non-ppi approach can cause a delay in the clearing of this GPIO as other Embassy tasks might become scheduled.
Unsafe is not required here given that all futures are required to live longer than their global peripheral instances. There are other occurrences of unsafe being used on new that should be removed. I started to do that but then went down a bit of a rabbit hole.
