This reverts commit f9f90b4173.
gbm_bo_get_modifier may return a modifier in these cases:
- The kernel doesn't support modifiers but Mesa does
- WLR_DRM_NO_MODIFIERS=1 is set
However, in both of these cases, the gbm_bo has been allocated
without modifiers.
There is already a check in drm_fb_create for modifiers:
wlr_drm_format_set_has will make sure buffers with an explicit
modifier will be rejected if the DRM backend doesn't support them.
So no need for an additional check in get_fb_for_bo.
Closes: https://github.com/swaywm/wlroots/issues/2896
The previous code would always print "falling back to legacy method",
even if the format wasn't ARGB8888.
Drop get_fb_for_bo_legacy, since the code can just be inlined without
hurting readability.
Ideally we should only fallback to drmModeAddFB if the error code
indicates the BE failure, but the original PR [1] doesn't say what
error code is returned by the kernel.
[1]: https://github.com/swaywm/wlroots/pull/2569
We shouldn't strip a modifiers from buffers, because the will make
the kernel re-interpret the data as LINEAR on most drivers,
resulting in an incorrect output on screen.
This is a type which manages gbm_surfaces and imported dmabufs in the
same place, and makes the lifetime management between the two shared. It
should lead to easier to understand code, and fewer special cases.
This also contains a fair bit of refactoring to start using this new
type.
Co-authored-by: Simon Ser <contact@emersion.fr>
We create the EGL config with GBM_FORMAT_ARGB8888, but then initialize GBM BOs
with GBM_FORMAT_XRGB8888. This mismatch confuses Mesa.
Instead, we can always use GBM_FORMAT_ARGB8888, and use DRM_FORMAT_XRGB8888
when calling drmModeAddFB2.
Fixes https://github.com/swaywm/wlroots/issues/1438
Values from libdrm are likely more reliable than raw values from the EDID. We
were already using values from libdrm, but they were overwritten by parse_edid.
See drm.c:
wlr_conn->output.phys_width = drm_conn->mmWidth;
wlr_conn->output.phys_height = drm_conn->mmHeight;
This commit allows outputs that need a CRTC to steal it from
user-disabled outputs. Note that in the case there are enough
CRTCs, disabled outputs don't loose it (so there's no modeset
and plane initialization needed after DPMS). CRTC allocation
still prefers to keep the old configuration, even if that means
allocating an extra CRTC to a disabled output.
CRTC reallocation now happen when enabling/disabling an output as
well as when trying to modeset. When enabling an output without a
CRTC, we realloc to try to steal a CRTC from a disabled output
(that doesn't really need the CRTC). When disabling an output, we
try to give our CRTC to an output that needs one. Modesetting is
similar to enabling.
A new DRM connector field has been added: `desired_enabled`.
Outputs without CRTCs get automatically disabled. This field keeps
track of the state desired by the user, allowing to automatically
re-enable outputs when a CRTC becomes free.
This required some changes to the allocation algorithm. Previously,
the algorithm tried to keep the previous configuration even if a
new configuration with a better score was possible (it only changed
configuration when the old one didn't work anymore). This is now
changed and the old configuration (still preferred) is only
retained without considering new possibilities when it's perfect
(all outputs have CRTCs).
User-disabled outputs now have `possible_crtcs` set to 0, meaning
they can only retain a previous CRTC (not acquire a new one). The
allocation algorithm has been updated to do not bump the score
when assigning a CRTC to a disabled output.
