More specifically, this removes services.pulseaudio and adds the option
hardware.pulseaudio.systemWide which defaults to false but can be used to turn
on the system-wide PulseAudio server (previously defined in
services.pulseaudio). Since the two PulseAudio modes are mutually exclusive
anyway (maybe not strictly true, but I don't think is a good idea combining
them) its nicer to be able to reuse server and ALSA configuration between them.
Also the system-wide PulseAudio service has been adjusted to systemd, and a few
things has been fixed (there was no alsa.conf before, for example).
The bottomline is that people that was using hardware.pulseaudio before should
be able to keep doing it in exactly the same way, and people that used
services.pulseaudio must switch over to hardware.pulseaudio.systemWide instead.
This makes it so multiple definitions are merged by adding a newline
between each entry, to avoid the need to add a newline to the end of
every definition of extraModprobeConfig. See #119 for an example of an
issue this has caused.
Signed-off-by: Shea Levy <shea@shealevy.com>
The smartd used to expect a list of devices to monitor. After this patch, it
expects a list of attribute sets, which may have two attributes:
- device: path to the device (required)
- options: smartd options to apply to this particular device (optional)
A concrete example configuration would be:
services.smartd = {
enable = true;
devices = [ { device = "/dev/sda"; } { device = "/dev/sdb"; options = "-d sat"; } ];
};
Furthermore, the config option 'deviceOpts' can be used to configure options
that are applied to *every* device.
Enable it with
services.transmission.enable = true;
and optionally configure it
services.transmission.settings =
{
download-dir = "/srv/torrents/";
incomplete-dir = "/srv/torrents/.incomplete/";
incomplete-dir-enabled = true;
rpc-whitelist = "127.0.0.1,192.168.*.*";
# for users in group "transmission" to have access to torrents
umask = 2;
};
The above settings are written/merged into settings.json each time the
service is about to start.
In principle this could work, but the current remount logic in nix fails
to remount mountpoints that are root in their own filesystem (as would
be the case with bind-mounting a mountpoint over itself). nixos/nix#98
is aimed at fixing this.
Signed-off-by: Shea Levy <shea@shealevy.com>
Newer kernels (since torvalds/linux@abb139e75c) try to
read firmware directly from the filesystem before falling back to a
userspace helper (udev) if firmware cannot be found (in even newer
kernels, the fallback path can be disabled altogether). By default, only
certain paths in /lib/firmware* are searched, so this was initially not
helpful for NixOS.
Since torvalds/linux@2760284206 (which,
based on the commit message, was implemented just for NixOS, go us!),
though, an extra path can be dynamically prepended to the search path.
So do that, in three ways:
1. Pass a kernel command line option in case the module is built-in
2. Add a line to modprobe.conf in case the module isn't yet loaded by
activation-time
3. Add an activation script to set the option in /sys in case the module
is already loaded by activation-time.
man logind.conf clearly states that the header is [Login] (no 'd').
Without this fix services.logind.extraConfig does not take effect
because logind ignores the invalidly named section.
So that we can customize systemd-logind in configuration.nix.
Example:
services.logind.extraConfig = "HandleLidSwitch=ignore";
See man logind.conf for available options.
xf86videovmware[1].
Adds "vmware" to list of default options of
services.xerver.videoDrivers.
new default:
[ "ati" "cirrus" "intel" "vesa" "vmware" ]
old default:
[ "ati" "cirrus" "intel" "vesa" ]
[1] Pull request for xf86videovmware found at
https://github.com/NixOS/nixpkgs/pull/338.
The mongodb service runs as user mongodb, and therefore
the preStart-script has no permissions to set up mongodb
directories. This is solved by adding an initialisation
service that runs as root and just sets up the required
directories.
This reverts commit 2802538dc2. The idea
was good, but unfortunately $GDFONTPATH has a different format, i.e.
programs that use this variable don't descend into the directories
listed here like fontconfig does, so we cannot use the same values for
both settings.
Set the environment variable GDFONTPATH to the list of directories where fonts
are expected to be installed. This is search path is used by same GD-based
applications, such as Gnuplot.
Alternatively, we could rely on fontconfig to achieve the same thing, i.e. by
running
for n in $(fc-list | sed -r -e 's|^([^:]+):.*$|\1|'); do echo $(dirname "$n"); done | sort | uniq
to get that list at run-time, but the static approach feels more deterministic.
